Doll Peasant Dress Pattern and Tutorial January 10, 2018 – Posted in: doll clothes, fat quarter, peasant dresses, sewing, tutorial
Peasant dresses are a really easy beginner sewing project. When I teach my daughters to sew doll clothes, this is our first lesson. I have to help with a few of the steps, but they can handle most of it.
After you learn how to make this basic dress, there are a lot of options to change it up for a totally different look. I also have tutorials for making peasant dresses in girls’ sizes. Matching girl/doll sets are always a pretty big hit!
These dresses have a lot of variations, and I hope to expand on this pattern in the future. For now, though, I am starting off simple with a basic, short sleeve peasant dress. I have picked up some tricks over the years to make sewing them a little faster and easier.
You will need:
- a fat quarter of fabric or 1/3 yard of fabric if bought from the bolt
- 8 1/2″ of 1/4″ wide elastic
- pins or wonder clips
- sewing machine and needles
- printed free pattern- available HERE
First, let’s prep the pattern. Print it out in actual size and cut it out. To fit the longer main dress piece on the page, I had to do it in two pieces. So, you will have to overlap the little bottom section and tape it together. It is off a little bit- about 1/8″ but I am not a professional and it is a free pattern so center it the best you can and don’t complain. OK?
If you want to be really efficient about it, fold it again, accordion style, and cut two of each pattern piece.
(If that was confusing, just ignore it and cut two pieces out individually!)
You will have four pieces total- a front, a back, and two sleeves.
One trick I learned through experience is that it is easier to hem the sleeves before sewing the dress together. Fold it under 1/4″ twice and sew 1/8″ from the edge. (My girls usually need help with this when they are first learning because it is such a small hem.)
Next, line up the curved edges of one sleeve and one dress piece as shown. Make sure to line up each set on the same side.
Sew the curves together with a 1/4″ seam allowance. (I also use a shorter stitch length to make those curves tighter.)
Then, sew the opposite side of each sleeve to the other side of the dress. This part used to confuse me, so I will show it at a couple of different angles.
Again, use a 1/4″ seam allowance. It is kind of like sewing everything together in a loop or a rectangle.
(Normally, I would nest the armpit seams so that one goes in each direction. It would lay flatter and be easier to sew. However, on this particular project, I like to face both of the seams towards the dress pieces, away from the sleeve hem. I just don’t want more bulk in that area. You can do whatever you like.)
Pin and sew along each side with a 1/4″ seam allowance.
Now, I happen to have an overlock machine, or serger. If you don’t have one, go buy one. They are awesome. If that isn’t an option or desire for you, you can finish the seam another way- pinking shears, zig zag stitch, etc. Google it.
Now, I happen to have created a separate tutorial for how to tuck in those serger threads. You can see it HERE.
Next you have to sew the elastic casing for the neckline. This is the hardest part, in my opinion. It just seems to take a little practice. The most important thing to remember is this: KEEP THE SEAMS ALL PRESSED IN THE SAME DIRECTION! Did that seem like I was shouting at you? Good. I was. Trust me. It is very frustrating to get the elastic stuck at a seam and this will prevent it.
Fold the raw edge down 1/4″ to the inside.
Next, fold it in 1/2″ (and watch those seams!) You can iron and pin. You can use wonder clips (those rock!) You can just eyeball it up and fold it as you sew (maybe after some practice). So that I could take a picture… I pinned this time.
Start sewing somewhere on the back. I like to start just before a seam. Sew about 1/8″ from the folded edge all the way around. I keep my needle to the left and line up the outside folded edge with the edge of my presser foot.
Do NOT go all the way around! Leave the last inch or so open so that you can put the elastic into the casing.
Cut a piece of 1/4″ elastic 8 1/2″ long. Pin a safety in onto each end. One will guide it through the casing. The other will keep the end from getting pulled in. (You can pin it to the dress if you want to be really sure!)
Make sure that you push the safety pin towards the seam so that everything is going the same direction.
Push the elastic all the way through the casing, being careful not to twist it.
Overlap the ends of the elastic about 3/4″ or so.
Use a small zig zag stitch on the machine to hold the ends together.
Stretch the casing to pull the elastic inside. Sew the opening closed.
Finally, turn the bottom under 1/4″ twice to make a small hem.
Stitch 1/8″ from the edge.
Hooray! It is finished!!!
To put it on the doll you will want to pull it up from the legs, not put it over the head. They are sort of disproportional so it is easier that way. Plus, you don’t mess the hair up.
Don’t forget to save the printable pattern…
You may also like…